These DLL-s contains only DCC Loader, thus it is to be used only for operations on DCC Read/Write page in the JTAG Manager.
Embedded DCC Loaders are designed to work inside of MCU's internal RAM memory, thus it is not sensitive to external SDRAM configuration or availability or its physical state.
This will enable You to work with wider variety of devices, based on QC CPU-s then usual model restricted DLL-s.
Initial H/W init sequience will setup MCU's PLL0 with these parameters:
L/M/N = 0x41/0x00/0x01;
Global Clock Divisor = DIV4
If you don't know what the L, M, N or Global Clock Divisor parameters are, then just keep in mind:
Highest L values and lowest Global Clock Divisor values will make maximum clocking frequency supplied to the MCU's core and thus DCC Read/Write speed will be maximum fast;
Too high frequency supplied to the MCU's core may result in core overheating or instable operation;
Once You download these DLL-s, You'll have new brand group in models list:
Resurrector QSC6XXX L36 D08 contains only DCC Loader, thus it is to be used only for operations on DCC Read/Write page in the JTAG Manager. Embedded DCC Loader is designed to work inside of MCU's internal RAM memory, thus it is not sensitive to external SDRAM configuration or availability or its physical state.
Initial H/W init sequence will setup MCU's PLL0 with these parameters:
L/M/N = 0x36/0x00/0x01;
Global Clock Divisor = DIV8
If you don't know what the L, M, N or Global Clock Divisor parameters are, then just keep in mind:
Highest L values and lowest Global Clock Divisor values will make maximum clocking frequency supplied to the MCU's core and thus DCC Read/Write speed will be maximum fast;
Too high frequency supplied to the MCU's core may result in core overheating or instable operation;
Momin_Telecom Admin And Forum Owner
Posts : 3062 Points : 8626 Thanks : 49 Join date : 2011-07-22 Age : 38
Resurrector AT91SAM9263-EK contains only DCC Loader, thus it is to be used only for operations on DCC Read/Write page in the JTAG Manager.
Embedded DCC Loader is designed to work inside of ATMEL AT91SAM9263 MCU's internal RAM memory. Loader has full (read/write) access to AT91SAM9263-EK evaluation board's NAND memory.
Currently only the 8-bit NAND interface is implemented.
Some people use this evaluation board to read various NAND chips content. [You must be registered and logged in to see this image.]
Momin_Telecom Admin And Forum Owner
Posts : 3062 Points : 8626 Thanks : 49 Join date : 2011-07-22 Age : 38
Resurrector ESM7XXX L41 D04 contains only DCC Loader, thus it is to be used only for operations on DCC Read/Write page in the JTAG Manager. Embedded DCC Loader is designed to work inside of MCU's internal RAM memory, thus it is not sensitive to external SDRAM configuration or availability or its physical state.
Initial H/W init sequence will setup MCU's PLL0 with these parameters:
L/M/N = 0x41/0x00/0x01;
Global Clock Divisor = DIV4
If you don't know what the L, M, N or Global Clock Divisor parameters are, then just keep in mind:
Highest L values and lowest Global Clock Divisor values will make maximum clocking frequency supplied to the MCU's core and thus DCC Read/Write speed will be maximum fast;
Too high frequency supplied to the MCU's core may result in core overheating or instable operation;
Momin_Telecom Admin And Forum Owner
Posts : 3062 Points : 8626 Thanks : 49 Join date : 2011-07-22 Age : 38
Resurrector QSC60XX L24 D08 contains only DCC Loader, thus it is to be used only for operations on DCC Read/Write page in the JTAG Manager. Embedded DCC Loader is designed to work inside of MCU's internal RAM memory, thus it is not sensitive to external SDRAM configuration or availability or its physical state.
Initial H/W init sequence will setup MCU's PLL with these parameters:
L/M/N = 0x2A/0x00/0x01;
Global Clock Divisor = DIV8
Resurrector QSC60XX L24 D08 contains only DCC Loader, thus it is to be used only for operations on DCC Read/Write page in the JTAG Manager. Embedded DCC Loader is designed to work inside of MCU's internal RAM memory, thus it is not sensitive to external SDRAM configuration or availability or its physical state.
Initial H/W init sequence will setup MCU's PLL with these parameters:
L/M/N = 0x20/0x00/0x01;
Global Clock Divisor = DIV8
You can use these two DLL-s with all QSC6xxx CPU devices with NOR flash. (Any CDMA phones with Qualcomm QSC60xx CPU, with NOR flash chip)
Momin_Telecom Admin And Forum Owner
Posts : 3062 Points : 8626 Thanks : 49 Join date : 2011-07-22 Age : 38
Resurrector PXA3XX contains only NAND DCC Loader, thus it is to be used only for operations on DCC Read/Write page in the JTAG Manager. Embedded DCC Loader is designed to work inside of MCU's internal RAM memory, thus it is not sensitive to external SDRAM configuration or availability or its physical state.
Momin_Telecom Admin And Forum Owner
Posts : 3062 Points : 8626 Thanks : 49 Join date : 2011-07-22 Age : 38
Resurrector QSC1100 X14 contains only DCC Loader, thus it is to be used only for operations on DCC Read/Write page in the JTAG Manager. Embedded DCC Loader is designed to work inside of MCU’s internal RAM memory, thus it is not sensitive to external SDRAM configuration or availability or its physical state.
Initial H/W init sequence will setup MCU’s PLL with these parameters:
Clock Multiplier = 0×14
Since few different versions of QSC1100 resurrector may exist (with different multiplier values) you may select the one which suits best to your device.
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
Momin_Telecom Admin And Forum Owner
Posts : 3062 Points : 8626 Thanks : 49 Join date : 2011-07-22 Age : 38
06.04.2011 QUALCOMM NOR QSC60XX L18 D08 Generic DLL Released
Resurrector QSC60XX L18 D08 contains only DCC Loader, thus it is to be used only for operations on DCC Read/Write page in the JTAG Manager. Embedded DCC Loader is designed to work inside of MCU's internal RAM memory, thus it is not sensitive to external SDRAM configuration or availability or its physical state.
Initial H/W init sequence will setup MCU's PLL with these parameters:
L/M/N = 0x18/0x00/0x01;
Global Clock Divisor = DIV8
If you don't know what the L, M, N or Global Clock Divisor parameters are, then just keep in mind:
Highest L values and lowest Global Clock Divisor values will make maximum clocking frequency supplied to the MCU's core and thus DCC Read/Write speed will be maximum fast;
Too high frequency supplied to the MCU's core may result in core overheating or instable operation;
Since few different versions of QSC60XX resurrector may exist (with different L or Global Clock Divisor parameters) you may select the one which suits best to your device.
Momin_Telecom Admin And Forum Owner
Posts : 3062 Points : 8626 Thanks : 49 Join date : 2011-07-22 Age : 38
08.04.2011 Generic Broadcom BCM2156 OneNAND DLL Released
Resurrector BCM2156 OneNAND 4K contains only DCC Loader, thus it is to be used only for operations on DCC Read/Write page in the JTAG Manager.
Embedded DCC Loader is designed to work inside of MCU's internal RAM memory, thus it is not sensitive to external SDRAM configuration or availability or its physical state.
Current DCC Loader is designed to work only with OneNAND devices which have page size 4096 bytes.
Momin_Telecom Admin And Forum Owner
Posts : 3062 Points : 8626 Thanks : 49 Join date : 2011-07-22 Age : 38
Added support for NOR Chips which have Intel/Sharp Extended Command Set (according to the CFI specification)
This means any NOR flash chip which is manufactured by CFI standard (it means all NOR flash chips) will be supported with above listed DLL-s. There is no need to update DCC Loaders for single flash chip ID, since configuration data are obtained from CFI.
Posts
Subject: * * * RIFF JTAG -Atmel, Broadcom, Marvell, Qualcom Generic NAND DCC Loaders * * 
Sat Sep 10, 2011 1:20 pm
