Resurrecting Haier C301R is simple. Phone is auto powered on with USB
Cable connected to the PC. Battery presence is not required; connection
can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0x257E

To resurrect Haier C301R:

• Solder JTAG cable to Haier C301R JTAG pads;
  
• Insert USB Data cable into board and PC;
  
• Make sure Haier C301R is selected in the list of models;
  
• Click Resurrect button;
  
• Choose which areas to flash;
  
• Wait till software signals a successful operation completion;
  
• De-solder JTAG wires;
  

[You must be registered and logged in to see this link.]

Resurrecting Olive C2110 is simple. Phone is auto powered on with USB
Cable connected to the PC. Battery presence is not required; connection
can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0×2254

To resurrect Olive C2110:

• Solder JTAG cable to Olive C2110 JTAG pads;
  
• Insert USB Data cable into board and PC;
  
• Make sure Olive C2110 is selected in the list of models;
  
• Click Resurrect button;
  
• Choose which areas to flash;
  
• Wait till software signals a successful operation completion;
  
• De-solder JTAG wires;
  

_

[You must be registered and logged in to see this link.]

JTAG Manager 1.38
---------------------------

• Added feature to disable Target ID check during resurrection
  

If current ID is not supported by a DLL, user can switch off ID check and still be able to try resurrection.
Though, we don't recommend it. Do it only if you are sure what you're doing and if you're sure that device
with unmatched target ID is still exactly the same model as stated in DLL.
Please note, upon JTAG Manager exe startup this option is automatically switched off.

To disable Target ID do the following:

-> Box Service -> Advanced Settings -> Tick "Ignore TARGET IDCODE . . ."

[You must be registered and logged in to see this image.]

• Added preset "Erase Full NAND/NOR Memory" (for this use Settings by Code button)
  

DCC operations presets will ensure proper use of DCC TAB features. To select DCC Operation preset, do the following:


-> DCC Read/Write TAB -> Settings By Code -> Select desired preset

[You must be registered and logged in to see this image.]



Firmware 1.29
---------------------------

• MPCore targets handling is improved.
  

• Fixed bug in the ARM7 handling routines: h/w breakpoints were disabled each time any halt operation was performed
  

Added auxiliary instruction which improves GDB Server functionality.

28.12.2011 Samsung Galaxy Note (GT-N7000) Unbrick – Dead Boot Repair supported

Samsung N7000 AP (PDA Part) is based on the S5PV310 (Exynos 4210) Processor (Cortex-A9 Dual-Core). JTAG pads are very small; professional experience in soldering is required to connect wires to the JTAG interface.
Note, one simple way to connect over JTAG – connect USB cable to PC and
insert battery. In this case phone is automatically powered on.

To resurrect Samsung N7000 AP:

• Solder JTAG cable to Samsung N7000 AP JTAG pads;
  
• Connect USB cable to phone and PC;
  
• Insert battery;
  
• Make sure Samsung N7000 AP is selected in the list of models;
  
• Make sure a fixed TCK frequency is selected;
  
• Click Resurrect button;
  
• Wait till software signals a successful operation completion;
  
• Disconnect USB cable, de-solder JTAG wires;
  

Now phone is in bootable condition, that is, even if it does not
start up normally, you can flash it using original Samsung downloader
software to restore it to the working state.

To enter download mode:

• Disconnect PC cable;
  
• Insert battery;
  
• Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.
  

_

[You must be registered and logged in to see this link.]

[You must be registered and logged in to see this link.]


Resurrecting HTC Glacier is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Some (or all) revisions of HTC Glacier boards have JTAG interface
disabled (that is enable MARM JTAG Fuse is ****n in the MSM7230 chip).
In this case the JTAG may be enabled only by firmware itself. This is
done by the FSBL loader, so writing to FSBL area is artificially
disabled in the DCC Loader code. DCC Loader will discard all flashing
attempts into FSBL zone and will respond with success code as if
flashing succeeded. In this way FSBL zone is protected while user still
can flash full image files seamlessly.
Resurrector will reflash radio’s boot zone (except FSBL area) and will
re-write SPL version 0.86.0000. Additionally to SPL and Radio zones, the
zone which contains Model ID is re-flashed too. Thus after resurrection
phone will have Model ID = ‘PD1510000’.
There is option to reflash BOOT and RECOVERY zones.
Please note, if your phone has the FSBL loader damaged and MCU has JTAG
FUSE ****n then there is no way to resurrect your phone via JTAG
interface.
To resurrect HTC Glacier:

• Solder JTAG cable to HTC Glacier JTAG pads;
  
• Insert batter and connect USB Data cable;
  
• Make sure HTC Glacier is selected in the list of models;
  
• If you use only battery, press Power On key;
  
• Click Resurrect button;
  
• Wait till software signals a successful operation completion;
  
• Disconnect power supply, de-solder JTAG wires;
  

Now
phone is in bootable condition, that is, even if it does not start up
normally you can flash it using known flashing methods.
To enter download mode:

• Disconnect PC cable;
  
• Insert battery;
  
• Hold ‘Volume Down’ key and press ‘Power ON’ button._
  [You must be registered and logged in to see this link.]
  

HTC Droid Incredible 2 ADR6350 Boot repair, Unlock, CID, ModelID, IMEI Update



Resurrecting HTC Incredible 2 (Droid Incredible 2 ADR6350VW) is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.

Some (or all) revisions of HTC Incredible 2 boards have JTAG interface
disabled (that is enable MARM JTAG Fuse is blown in the MSM8655 chip).
In this case the JTAG may be enabled only by firmware itself. This is
done by the FSBL loader, so writing to FSBL area is artificially
disabled in the DCC Loader code. DCC Loader will discard all flashing
attempts into FSBL zone and will respond with success code as if
flashing succeeded. In this way FSBL zone is protected while user still
can flash full image files seamlessly.

Resurrector will reflash radio’s boot zone (except FSBL area) and will re-write PDA’s SPL version 6.13.1002.
Additionally to SPL and Radio zones, the zone which contains Model ID
is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG3210***’.

There is option to reflash BOOT and RECOVERY zones.

Please note, if your phone has the FSBL loader damaged and MCU has JTAG
FUSE blown then there is no way to resurrect your phone via JTAG
interface.
To resurrect HTC Incredible 2:

• Solder JTAG cable to HTC Incredible 2 JTAG pads;
  
• Insert batter and connect USB Data cable;
  
• Make sure HTC Incredible 2 is selected in the list of models;
  
• If you use only battery, press Power On key;
  
• Click Resurrect button;
  
• Wait till software signals a successful operation completion;
  
• Disconnect power supply, de-solder JTAG wires;
  

Now phone is in bootable condition, that is, even if it does not
start up normally you can flash it using known flashing methods.
To enter download mode:

• Disconnect PC cable;
  
• Insert battery;
  
• Hold ‘Volume Down’ key and press ‘Power ON’ button.
  

_


[You must be registered and logged in to see this link.]

09.02.2012 Samsung Galaxy Precedent SCH-M828 Unbrick supported


Samsung M828 resurrection is simple. Phone is auto
powered when USB Data Cable is inserted while battery is inside. If you
don’t use USB cable, make sure to hold Power On button during JTAG
connection establishing phase.
To resurrect Samsung M828 do this:

• Solder JTAG cable to Samsung M828 JTAG pads;
  
• Insert battery and connect USB cable to phone and PC;
  
• Make sure Samsung M828 is selected in the list of models;
  
• Click Resurrect button;
  
• Wait few seconds until software signals a successful operation completion;
  
• Disconnect USB cable, de-solder JTAG wires;
  

Now phone is in bootable condition, that is, even if it does not
start up normally, you can flash it using original Samsung downloader
software to restore it to the working state.

To enter download mode:

• Disconnect PC cable;
  
• Insert battery;
  
• Hold both ‘Volume Down’ and ‘Camera’ keys and press Power-On to enter Download Mode;
  

_
[You must be registered and logged in to see this link.]

[You must be registered and logged in to see this link.]
Resurrecting HTC Thunderbolt CP (Modem Part) part is easy.
Phone is auto powered on with USB Data Cable connected to the PC while
battery is inside; sometimes during connection pressing Power On key may
be required.
Please note, CP Part’s power is controlled by the
AP Part, thus you may experience constant connection loses after
definite ammounts of time (1-2-5-x seconds). If this keeps interferring
the resurrection process, solder additionall JTAG interface cable to the
AP pads, select AP resurrector DLL, go to the JTAG Read/Write page and
halt AP core, then switch back to the CP JTAG interface.
To resurrect HTC Thunderbolt CP (Modem Part) Part:

• Solder JTAG cable to HTC Thunderbolt CP JTAG pads;
  
• Insert USB Data cable into board and PC;
  
• Make sure HTC Thunderbolt CP is selected in the list of models;
  
• Click Resurrect button;
  
• Wait till software signals a successful operation completion;
  
• Disconnect power supply, de-solder JTAG wires;
  

Now
phone is in bootable condition, that is, even if it does not start up
normally, you can flash it using known flashing methods.
Resurrecting HTC Thunderbolt AP (PDA Part) is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.04.0000
version. Additionally to SPL and Radio zones, the zone which contains
Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG0510000’.
There is option to reflash BOOT and RECOVERY zones.
_
[You must be registered and logged in to see this link.]

24.02.2012 Samsung YP-G70EW Galaxy S WiFi 5.0 Unbrick – Boot repair, World first ! ! !


Samsung YP-G70 is based on the S5PCxxx Processor (ARM core is Cortex-A8).
Note, one simple way to connect over JTAG – connect USB cable to PC and
insert battery. In this case phone is automatically powered on. But
note, in very rare cases it is possible that you will have to hold Power
On key during initial connection.
To resurrect Samsung YP-G70:

• Solder JTAG cable to Samsung YP-G70 JTAG pads;
  
• Connect microUSB cable to phone and PC;
  
• Insert battery;
  
• Make sure Samsung YP-G70 is selected in the list of models;
  
• Make sure a fixed TCK frequency is selected;
  
• Click Resurrect button;
  
• Wait till software signals a successful operation completion;
  
• Disconnect USB cable, de-solder JTAG wires;
  

Now
phone is in bootable condition, that is, even if it does not start up
normally, you can flash it using original Samsung downloader software to
restore it to the working state.
To enter download mode:

• Disconnect PC cable;
  
• Insert battery;
  
• Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.
  

.
[You must be registered and logged in to see this link.]

28.02.2012 Samsung SGH-i777 Galaxy S II Unbrick – Boot Repair supported, World First ! ! !

Samsung I777 is based on the S5PV310 (Exynos 4210) Processor (Cortex-A9 Dual-Core). JTAG pads are very small; professional experience in soldering is required to connect wires to the JTAG interface.
Note, one simple way to connect over JTAG – connect USB cable to PC and
insert battery. In this case phone is automatically powered on.

To resurrect Samsung I777:

• Solder JTAG cable to Samsung I777 JTAG pads;
  
• Connect USB cable to phone and PC;
  
• Insert battery;
  
• Make sure Samsung I777 is selected in the list of models;
  
• Make sure a fixed TCK frequency is selected;
  
• Click Resurrect button;
  
• Wait till software signals a successful operation completion;
  
• Disconnect USB cable, de-solder JTAG wires;
  

Now phone is in bootable condition, that is, even if it does not
start up normally, you can flash it using original Samsung downloader
software to restore it to the working state.

To enter download mode:

• Disconnect PC cable;
  
• Insert battery;
  
• Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.
  

.
[You must be registered and logged in to see this link.]

28.02.2012 Samsung GT-S7500 Galaxy Ace Plus Unbrick – Boot Repair supported, World First ! ! !

Resurrecting Samsung S7500 is easy.
Note, one simple way to connect over JTAG – connect USB cable to PC and
insert battery. In this case phone is automatically powered on, so no
need to press any power-on buttons on the phone keypad.

To resurrect Samsung S7500:

• Solder JTAG cable to Samsung S7500 JTAG pads;
  
• Insert USB Data cable into board and PC;
  
• Make sure Samsung S7500 is selected in the list of models;
  
• Click Resurrect button;
  
• Wait till software signals a successful operation completion;
  
• Disconnect power supply, de-solder JTAG wires;
  

Now phone is in bootable condition, that is, even if it does not
start up normally, you can flash it using known flashing methods.

To enter download mode:

• Disconnect PC cable;
  
• Insert battery;
  
• Hold ‘Volume Down’ and ‘Home’ keys and press Power-On.
  

.
[You must be registered and logged in to see this link.]

[You must be registered and logged in to see this link.]


by [You must be registered and logged in to see this link.] on Mar.01, 2012, under [You must be registered and logged in to see this link.]


01.03.2012 Samsung GT-S5360 Galaxy Y Unbrick – Boot repair supported

Resurrecting Samsung S5360 is easy. To power the phone connect USB
cable and insert battery. Sometimes it’s needed to press Power On key.
In case phone is not detected de-power phone completely, then wait few seconds, insert USB cable and then insert battery.

To resurrect Samsung S5360:

• Solder JTAG cable to Samsung S5360 JTAG pads;
  
• Connect USB cable to phone and PC;
  
• Insert battery;
  
• Make sure Samsung S5360 is selected in the list of models;
  
• Click Resurrect button;
  
• Wait till software signals a successful operation completion;
  
• Disconnect USB cable, de-solder JTAG wires;
  

Now phone is in bootable condition, that is, even if it does not
start up normally, you can flash it using original Samsung downloader
software to restore it to the working state.

To enter download mode:

• Disconnect PC cable;
  
• Insert battery;
  
• Hold both ‘Volume Down’ and ‘Menu’ keys and press Power-On.
  
• If nothing happens, try an alternative: hold both ‘Volume Up’ and ‘Menu’ keys and press Power-On.
  

.
[You must be registered and logged in to see this link.]

06.03.2012 RIFF JTAG – Samsung SGH-T499 Dart (Samsung Tass) Unbrick – Boot Repair supported


Repairing
bricked Samsung T499 is easy with RIFF Box. Phone is auto powered on
with USB Data Cable connected to the PC while battery is inside. In case
you use the battery only please note you will have to press Power On
key once.
To resurrect Samsung T499:

• Solder JTAG cable to Samsung T499 JTAG pads;
  
• Make sure Samsung T499 is selected in the list of models;
  
• Insert Battery into phone and connect USB cable (in case you not use USB cable, press once the Power ON key on the phone)
  
• Click Resurrect button;
  
• Wait till software signals a successful operation completion;
  
• Disconnect USB cable, de-solder JTAG wires;
  

Now
phone is in bootable condition, that is, even if it does not start up
normally, you can flash it using known flashing methods.
To enter download mode:

• Disconnect PC cable;
  
• Insert battery;
  
• Hold both ‘Volume Up’ and ‘Home’ keys and press ‘Power ON’ button. In few seconds phone enters download mode.
  

.
[You must be registered and logged in to see this link.]


Update was done in 20 minutes, thanks to user Trung from Vietnam !

13.03.2012 RIFF JTAG – SonyEricsson new BOOTROM support and more !

Whats new:

Unlock/Repair TA is now supported for new BOOTROM version in following models:

• E15a (SE_E15a.dll),
  
• E15i (SE_X8.dll),
  
• U20a (SE_U20a.dll),
  
• U20i (SE_U20i.dll),
  
• E10i (SE_X10_Mini.dll)
  

HTC Neon Unbrick – Boot Repair, IMEI and CID update supported.




[You must be registered and logged in to see this link.]
:[You must be registered and logged in to see this link.], [You must be registered and logged in to see this link.], [You must be registered and logged in to see this link.], [You must be registered and logged in to see this link.], [You must be registered and logged in to see this link.], [You must be registered and logged in to see this link.], [You must be registered and logged in to see this link.], [You must be registered and logged in to see this link.]







[You must be registered and logged in to see this link.]


by [You must be registered and logged in to see this link.] on Mar.12, 2012, under [You must be registered and logged in to see this link.]


12.03.2012 RIFF JTAG – LG P350 Pecan / Optimus Me Unbrick – Boot Repair supported

Resurrecting LG P350 is very hard because it requires non-beginner
soldering skills (since JTAG pads on board are very small and are close
to each other).
Phone is auto powered on with USB Data Cable connected to the PC.
Battery presence is not required; connection can be established with
detached board.

To resurrect LG P350:

• Solder JTAG cable to LG P350 JTAG pads;
  
• Insert USB Data cable into board and PC;
  
• Make sure LG P350 is selected in the list of models;
  
• Click Resurrect button;
  
• Wait till software signals a successful operation completion;
  
• Disconnect power supply, de-solder JTAG wires;
  

Now phone is in bootable condition, that is, even if it does not
start up normally, you can flash it using known flashing methods. We
used KDZ_FW_UPD update software (with settings Type = 3GQCP, PhoneMode =
EMERGENCY) to flash the *.KDZ firmware into phone.

To enter emergency mode:

• Disconnect PC cable;
  
• Insert battery;
  
• Hold ‘Volume down’ key and press ‘Power ON’ button. In few seconds you should see emergency mode screen saying “DOWNLOAD MODE”.
  

.
[You must be registered and logged in to see this link.]

14.03.2012 RIFF JTAG – T-Mobile Samsung SGH-T989 Galaxy S II Unbrick – Dead Boot Repair supported, World First ! ! !

Repairing bricked Samsung T989 is easy with the RIFF Box. The device is based on the Qualcomm APQ8060 chipset.
Note, one simple way to connect over JTAG – connect USB cable to PC and
insert battery. In this case phone is automatically powered on.

To resurrect Samsung T989:

• Solder JTAG cable to Samsung T989 JTAG pads;
  
• Connect USB cable to phone and PC;
  
• Insert battery;
  
• Make sure Samsung T989 is selected in the list of models;
  
• Click Resurrect button;
  
• Wait till software signals a successful operation completion;
  
• Disconnect USB cable, de-solder JTAG wires;
  

Now phone is in bootable condition, that is, even if it does not
start up normally, you can flash it using original Samsung downloader
software to restore it to the working state.

To enter download mode:

• Disconnect PC cable;
  
• Insert battery;
  
• Hold ‘Volume Down’ key and press Power-On.
  

.
[You must be registered and logged in to see this link.]

Hello dear RIFF Box users !


Time to time we need help from our users, in order to improve our support and increase list of supported devices.


In this topic I'll post wanted stuff, so users who provide help here will have priority when they need support.

15.03.2012 Important - RIFF Box HUAWEI Phones Support

Wanted following Huawei Models:

• U8110 (Dead)
  
• U8120 (Dead)
  
• U8150(Dead)
  
• U8230(Dead)
  
• U8300 (Dead)
  
• U8510 (Dead)
  
  
• U8650 (Working)
  
  
• U8800 (Working)
  
  
• U8860 (Working)
  
• Any other Huawei model
  

If You have any of above mentioned models, please contact me via ICQ or Sonork for further steps.




Dead phones needed for beta tests :

• Samsung T589
  
• LG E510
  

Working phone full dumps :

• LG E510
  

Phones needed in Ukraine, Kiev :


Any HTC Model, based on QUALCOMM MSM82xx CPU, in QHUSB_DLOAD mode (Error 0X44 on JTAG)

List of models:

• HTC Desire HD
  
• HTC Desire S
  
• HTC Desire Z
  
• HTC Sensation
  
• HTC Inspire
  
• Any other model based on MSM8255, MSM8260
  

Any Samsung model (Working or Bricked), based on QUALCOMM APQ8060 CPU


List of models:

• Samsung i717
  
• Samsung E160S
  
• Samsung E110s
  

PCB Photos we need :

• Any of not supported model !
  

Photos must be made in high resolution, if possible on daylight, without use of flash or artificial light.


Good photo sample :

[You must be registered and logged in to see this image.]




If You can help for any of above mentioned requests, please contact me via Sonork or ICQ.

23.03.2012 RIFF JTAG – LG E510 Optimus Hub (LG Univa) Supported
Repairing bricked LG E510 with the RIFF Box is not very hard but it
requires non-beginner soldering skills (since JTAG pads on board are
very small and are close to each other).
Phone is auto powered on with USB Data Cable connected to the PC.
Battery presence is not required; connection can be established with
detached board.

To resurrect LG E510:

• Solder JTAG cable to LG E510 JTAG pads;
  
• Insert USB Data cable into board and PC;
  
• Make sure LG E510 is selected in the list of models;
  
• Click Resurrect button;
  
• Wait till software signals a successful operation completion;
  
• Disconnect power supply, de-solder JTAG wires;
  

Now phone is in bootable condition, that is, even if it does not
start up normally, you can flash it using known flashing methods

To enter emergency mode:

• Disconnect PC cable;
  
• Insert battery;
  
• Hold ‘Volume down’ key and press ‘Power ON’ button. In few seconds you should see emergency mode screen saying “DOWNLOAD MODE”.
  

.
[You must be registered and logged in to see this link.]

OCK DUMP [You must be registered and logged in to see this link.]

DOWNLOAD AND ENJOY [You must be registered and logged in to see this link.]